Rubber Hoses
Product Code: RH/A
EMFLEX rubber hoses are used as an economical final connection to fancoil units. They are designed to offer a high degree of flexibility to allow for misalignment of the pipework and the suppression of possible vibration from the fancoil unit. The basic hose connector is available in varying standard lengths, although almost any length can be manufactured. Double shut-off quick release couplings are available to allow immediate removal of the fancoil unit in the event of break-down or for maintenance purposes. A great deal of time and money can be saved by an engineer if the need to drain down is eliminated by the use of hoses and quick release couplings.
Product Type
Info Table
Additional Information
A high quality EPDM hose and stainless steel over braiding with nickel plated brass end fittings. Suitable for heating circuits. BSRIA cycle tested in excess of an estimated 12 yrs of simulated operation.
A high quality EPDM hose and stainless steel over braiding with nickel plated brass end fittings. With 9mm thick ‘Armaflex’ Class ‘0’ insulation and vapour seal. Suitable for chilled water circuits.
- Nominal Size
- mm
- 15
- 20
- 25
- Minimal Static Bend Radius
- mm
- 70
- 90
- 110
- Overall Length 1
- mm
- 300
- 300
- 300
- Overall Length 2
- mm
- 450
- 450
- 450
- Overall Length 3
- mm
- 600
- 600
- 600
Pressures
Work Pressure: 10 bar (1000 kPa) for all sizes.
Test Pressure: 1.5 x Working Pressure.
Temperature: 90ºC maximum.
End fittings available:
1. Fixed male BSP taper thread.
2. Flat faced female swivel nut, BSP parallel thread, for use with rubber washer.
3. Compression fitting.
4. Brass standpipe.
5. All above with 90 degree elbow.
Please note that the stated overall lengths may need to increase with the use of different end fittings.
+ -
Emflex
RUBBER HOSE
N.Minikin & Sons LimitedUnit 2B Brickyard Road, Roecliffe, York, YO51 9NS
Email: enquiries@minikins.co.uk Web: www.minikins.co.uk
Tel: 01423 326 789
01423 326 789
N.MINIKINS & SONS LIMITED
MINIKINS.CO.UK
Rubber HosesProduct Code: RH/A
EMFLEX rubber hoses are used as an economical final connection to fancoil units. They are designed to offer a high degree of flexibility to allow for misalignment of the pipework and the suppression of possible vibration from the fancoil unit. The basic hose connector is available in varying standard lengths, although almost any length can be manufactured. Double shut-off quick release couplings are available to allow immediate removal of the fancoil unit in the event of break-down or for maintenance purposes. A great deal of time and money can be saved by an engineer if the need to drain down is eliminated by the use of hoses and quick release couplings.
A high quality EPDM hose and stainless steel over braiding with nickel plated brass end fittings. Suitable for heating circuits. BSRIA cycle tested in excess of an estimated 12 yrs of simulated operation.
A high quality EPDM hose and stainless steel over braiding with nickel plated brass end fittings. With 9mm thick ‘Armaflex’ Class ‘0’ insulation and vapour seal. Suitable for chilled water circuits.
- Nominal Size
- mm
- 15
- 20
- 25
- Minimal Static Bend Radius
- mm
- 70
- 90
- 110
- Overall Length 1
- mm
- 300
- 300
- 300
- Overall Length 2
- mm
- 450
- 450
- 450
- Overall Length 3
- mm
- 600
- 600
- 600
Pressures
Work Pressure: 10 bar (1000 kPa) for all sizes.
Test Pressure: 1.5 x Working Pressure.
Temperature: 90ºC maximum.
End fittings available:
1. Fixed male BSP taper thread.
2. Flat faced female swivel nut, BSP parallel thread, for use with rubber washer.
3. Compression fitting.
4. Brass standpipe.
5. All above with 90 degree elbow.
Please note that the stated overall lengths may need to increase with the use of different end fittings.
01423 326 789
N.MINIKINS & SONS LIMITED
MINIKINS.CO.UK